smartd automated scanning failing
Ubence Quevedo
thatrat at gmail.com
Sat Dec 6 01:42:10 PST 2014
> What happens if you run smartd manually in debug mode and without forking:
> sudo port unload smartmontools
> sudo /opt/local/sbin/smartd -n -d -c /opt/local/etc/smartd.conf
>
> When I ran manually without sudo smartd complained about not being able to write a state file to:
> /opt/local/var/lib/smartmontools/smartd.Hitachi_HDS722020ALA330-JK1174YAK4MZ3W.ata.state
>
When I ran the smartd like you did from the command line like the above, it seems to work properly:
Ubences-Intel-iMac:etc uquevedo$ sudo /opt/local/sbin/smartd -n -d -c /opt/local/etc/smartd.conf
smartd 6.2 2013-07-26 r3841 [x86_64-apple-darwin14.0.0] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
Opened configuration file /opt/local/etc/smartd.conf
Configuration file /opt/local/etc/smartd.conf parsed.
Device: /dev/disk0, opened
Device: /dev/disk0, WDC WD1002FAEX-00Y9A0, S/N:[not showing this], WWN:5-0014ee-2064339e8, FW:05.01D05, 1.00 TB
Device: /dev/disk0, found in smartd database: Western Digital Caviar Black
Device: /dev/disk0, is SMART capable. Adding to "monitor" list.
Device: /dev/disk0, state read from /opt/local/var/lib/smartmontools/smartd.WDC_WD1002FAEX_00Y9A0-WD_WCAW32908017.ata.state
Monitoring 1 ATA and 0 SCSI devices
Device: /dev/disk0, opened ATA device
Device: /dev/disk0, state written to /opt/local/var/lib/smartmontools/smartd.WDC_WD1002FAEX_00Y9A0-WD_WCAW32908017.ata.state
Device: /dev/disk0, opened ATA device
Device: /dev/disk0, opened ATA device
Device: /dev/disk0, starting scheduled Short Self-Test. <— The short test that I had scheduled in smartd.conf
Device: /dev/disk0, state written to /opt/local/var/lib/smartmontools/smartd.WDC_WD1002FAEX_00Y9A0-WD_WCAW32908017.ata.state
Device: /dev/disk0, opened ATA device
.
.
.
Device: /dev/disk0, opened ATA device
Device: /dev/disk0, starting scheduled Long Self-Test. <— The long test that I had scheduled in smartd.conf
Device: /dev/disk0, state written to /opt/local/var/lib/smartmontools/smartd.WDC_WD1002FAEX_00Y9A0-WD_WCAW32908017.ata.state
Device: /dev/disk0, opened ATA device
.
.
.
Ubences-Intel-iMac:etc uquevedo$ smartctl -a /dev/disk0
smartctl 6.2 2013-07-26 r3841 [x86_64-apple-darwin14.0.0] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Black
Device Model: WDC WD1002FAEX-00Y9A0
Serial Number: [hiding this again]
LU WWN Device Id: 5 0014ee 2064339e8
Firmware Version: 05.01D05
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Dec 6 01:28:35 2014 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (16860) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 174) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 13
3 Spin_Up_Time 0x0027 172 170 021 Pre-fail Always - 4391
4 Start_Stop_Count 0x0032 076 076 000 Old_age Always - 24330
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 5098
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 079 079 000 Old_age Always - 21825
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 21
193 Load_Cycle_Count 0x0032 192 192 000 Old_age Always - 24308
194 Temperature_Celsius 0x0022 100 081 000 Old_age Always - 47
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 1
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 5093 -
# 2 Extended offline Completed without error 00% 5082 -
# 3 Short offline Completed without error 00% 5069 -
# 4 Short offline Completed without error 00% 5066 -
# 5 Extended offline Completed without error 00% 4673 -
# 6 Extended offline Completed without error 00% 4080 -
# 7 Short offline Completed without error 00% 2987 -
# 8 Extended offline Aborted by host 80% 2985 -
# 9 Short offline Completed without error 00% 2982 -
#10 Short offline Completed without error 00% 2975 -
#11 Short offline Aborted by host 90% 2962 -
#12 Short offline Completed without error 00% 2960 -
#13 Short offline Completed without error 00% 2957 -
#14 Short offline Completed without error 00% 2956 -
#15 Short offline Completed without error 00% 2950 -
#16 Short offline Completed without error 00% 2948 -
#17 Short offline Completed without error 00% 2946 -
#18 Short offline Completed without error 00% 2944 -
#19 Short offline Completed without error 00% 2941 -
#20 Short offline Completed without error 00% 2939 -
#21 Short offline Completed without error 00% 2934 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
There is an entry on the Mac Ports Trac site for an upgrade to 6.3 here: https://trac.macports.org/ticket/45982 <https://trac.macports.org/ticket/45982>
I’m going to try compiling smartmontools from source and give that a try to see if I still run into the same issue and hope that the 6.3 update whenever it is released from Mac Ports will fix this problem.
I’ll also likely post a bug report since there doesn’t seem to be one for this already.
-Ubence
> Regards,
> Bradley Giesbrecht (pixilla)
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.macosforge.org/pipermail/macports-users/attachments/20141206/321155c5/attachment.html>
More information about the macports-users
mailing list